1 00:00:00,120 --> 00:00:06,240 So now will try to understand how we use a dual channel rate, so we already understand how we could 2 00:00:06,240 --> 00:00:12,090 use the single channel and how we could read, as well as write the detail and then GPI peripheral in 3 00:00:12,090 --> 00:00:18,600 this specific video will be focusing on what are the differences that you find when we utilize the multiple 4 00:00:18,600 --> 00:00:20,010 channels of the sea. 5 00:00:20,380 --> 00:00:20,610 Right. 6 00:00:20,610 --> 00:00:27,300 So the fundamental hardware consisting of a microplates and you are late is already been added, and 7 00:00:27,300 --> 00:00:31,010 this is generated with the help of a PC script that we discuss, right? 8 00:00:31,230 --> 00:00:36,110 So we'll go away and try to add that UPI IP right now here. 9 00:00:36,120 --> 00:00:39,520 We want to configure this IP to have a multiple channel right now. 10 00:00:39,540 --> 00:00:44,520 You could see by default, it only have a single channel, so we double click on an IP. 11 00:00:44,730 --> 00:00:48,580 OK, and here we will be configuring both the channel right. 12 00:00:48,600 --> 00:00:49,560 So let it disconnect. 13 00:00:49,560 --> 00:00:52,370 First channel to the switch. 14 00:00:52,440 --> 00:00:58,350 OK, so those light switch that we have on the board and the second channel to any right to our edge, 15 00:00:58,350 --> 00:01:03,840 and that will be whatever data that we have on and slate search, we will be sending the CMT down any 16 00:01:04,140 --> 00:01:04,400 right. 17 00:01:04,410 --> 00:01:10,800 So these are the two channel and you could also see on preview that now our IP have two output ports, 18 00:01:10,800 --> 00:01:11,030 right? 19 00:01:11,040 --> 00:01:16,260 So one of them will be connected to the slide switch and they will be connected to any lady, right? 20 00:01:16,530 --> 00:01:21,900 Remember this that first channel is where we have connected a switch, right? 21 00:01:21,930 --> 00:01:28,200 Because when we write an application and there, we need to correctly specify the direction for the 22 00:01:28,200 --> 00:01:29,010 specific channel. 23 00:01:29,070 --> 00:01:29,370 Right? 24 00:01:29,550 --> 00:01:35,040 So first channel is where we have a switch, so it should be configured such that we are able to sense 25 00:01:35,040 --> 00:01:36,510 the value from a switch, right? 26 00:01:36,870 --> 00:01:43,080 And the second channel should be configured so that microplates will be able to write that down to iterate. 27 00:01:43,110 --> 00:01:45,360 So let it just go ahead and try to click OK. 28 00:01:45,630 --> 00:01:50,140 So once you customize your IP, you are ready to perform connection automation. 29 00:01:50,160 --> 00:01:51,060 So here we will be. 30 00:01:51,060 --> 00:01:54,560 Selecting all the power for this will do is this will connect thusly. 31 00:01:54,570 --> 00:02:01,710 We see interface that we have on and you'd be able to do a CDP port of fire. 32 00:02:02,370 --> 00:02:07,300 And along with that, it will also connect the two port to their respective pins. 33 00:02:09,180 --> 00:02:12,390 So once this is done, we are ready with our hardware. 34 00:02:12,660 --> 00:02:13,050 OK? 35 00:02:13,140 --> 00:02:15,210 That could be used to bring up an application. 36 00:02:15,240 --> 00:02:18,540 So we'll just proceed to validate our design. 37 00:02:18,540 --> 00:02:24,600 And once validation is successful, OK, we will be going ahead and counting the number of ports that 38 00:02:24,600 --> 00:02:25,680 we have in our design. 39 00:02:25,690 --> 00:02:30,090 So we have one two and then three, four and five ports, right? 40 00:02:30,360 --> 00:02:37,050 So we go to a boat tab and we'll be calculating the checkmarks that we have for up to fit into one two 41 00:02:37,770 --> 00:02:39,930 three four five, right? 42 00:02:39,930 --> 00:02:40,890 So we have five check. 43 00:02:41,160 --> 00:02:47,890 So we are ready to proceed for generation of NHL wrapper and one KHL wrapper is generated. 44 00:02:47,910 --> 00:02:54,510 We could proceed for generation of object system since all the ports are connected to their respective 45 00:02:55,080 --> 00:02:55,830 peripherals. 46 00:02:57,190 --> 00:03:01,210 So Rapid is ready now we will proceed for generation of.