1
00:00:08,000 --> 00:00:19,000
Today, I will tell you how to interface infrared sensor with LabView using Ardino Neno so or here we

2
00:00:19,000 --> 00:00:23,000
have Ardino Nano and I just made the connections.

3
00:00:24,000 --> 00:00:26,000
So on.

4
00:00:26,000 --> 00:00:30,000
The audio module will be have weak ground and one output.

5
00:00:30,000 --> 00:00:39,000
So I just connect the output with the five pin and Bleckmann is my ground and that one is my VXI.

6
00:00:39,000 --> 00:00:49,000
So as you see over here, when I put my hand in the front or on the front of this Allard's blink, it

7
00:00:49,000 --> 00:00:50,000
will generate a signal.

8
00:00:50,000 --> 00:00:56,000
And when you remove my hand, balladeers goes off on hold on hold.

9
00:00:57,000 --> 00:01:01,000
So this is the indication that my module is working.

10
00:01:01,000 --> 00:01:05,000
So I just go to the software part so you have to interface.

11
00:01:05,000 --> 00:01:13,000
You are already nonono with Lendu from the tools maker hub line from where we are.

12
00:01:14,000 --> 00:01:24,000
Then go, just go to the we walk over here, we have the tool box so fast, the same procedure Waupun

13
00:01:25,000 --> 00:01:28,000
laws and in this case I have to just leave.

14
00:01:28,000 --> 00:01:29,000
There is no signal.

15
00:01:30,000 --> 00:01:32,000
So just this one.

16
00:01:36,000 --> 00:01:51,000
This this connectedness, so here we have our computer that is complex and then we have to take the

17
00:01:51,000 --> 00:01:56,000
borate, in this case it is nine six that zero.

18
00:01:57,000 --> 00:02:00,000
This is the same borate in the case of Ardino also.

19
00:02:01,000 --> 00:02:04,000
But in the case of Maiga, it is different.

20
00:02:04,000 --> 00:02:07,000
So all here you have to just select the PIN number.

21
00:02:07,000 --> 00:02:15,000
Right now, the PIN number has been number five and over here you have to just select the balloon.

22
00:02:17,000 --> 00:02:19,000
So order here.

23
00:02:19,000 --> 00:02:21,000
This is the balloon, Élodie.

24
00:02:24,000 --> 00:02:37,000
To display the output of I have said this and I just use Willaura for continuous reading control and

25
00:02:37,000 --> 00:02:41,000
then just go through the error handler.

26
00:02:42,000 --> 00:02:45,000
The procedure is the same in all the cases.

27
00:02:45,000 --> 00:02:53,000
Just you have to just check out the dataset of different sensors, like some sensors generate does signal

28
00:02:53,000 --> 00:03:02,000
sometimes out of analog signals, sometimes have acquired analog signals, some sensors required, not

29
00:03:02,000 --> 00:03:09,000
sensors that are like relay, some required signals, some required analog signal.

30
00:03:09,000 --> 00:03:12,000
So according to that, you have to program.

31
00:03:13,000 --> 00:03:16,000
So this is the program.

32
00:03:16,000 --> 00:03:17,000
It is ready.

33
00:03:17,000 --> 00:03:22,000
So when I say don't run button, as you see right now, then ladies off.

34
00:03:22,000 --> 00:03:26,000
And when I hit on, when I place my hand.

35
00:03:27,000 --> 00:03:31,000
So it is going off and over here again, daylilies goes on.

36
00:03:32,000 --> 00:03:40,000
So when I remove my hand, LRAD goes off, on or on, off, on, off.

37
00:03:40,000 --> 00:03:42,000
So this is how you can interface.

38
00:03:42,000 --> 00:03:45,000
I came up with you.

39
00:03:45,000 --> 00:03:45,000
Thank you.